THE MYSTERIOUS POWERS OF CORAL CASTLE
PRESENTED BY PARANORMAL-INVESTIGATION.COM

What I have done is taken what I have learned and devised a way to not have the magnetic lock even come into play. Not to try and over come it, just get rid of the thing. I mean it‘s useless anyway Right?. In the TOMI device the magnetic lock occurs when the runner has traveled the full length of the tracks and got stuck at the top.

In a gravity setup like the ramps and other methods of using TOMI the traveling distance and the bulk of the ramps really produce a very low amount of work in relation to what they can produce if one took away the ramp and used the setup on a flat spinning plane instead. So take a look at the picture to the left and imagine the curved bar magnet is magnetized throughout the circumference.The poles would be in line with the arrows. This would be a perfect ring magnet except for the fact that a 60 degree segment is missing from it. The reason for that is that if the segment was still there the magnetic field would be continuous and it would then be a closed loop so to speak. That would be useless.

Here you can see the interaction of a roller or now we would call this a drive magnet. Imagining the curved magnet on a rotating plane, you will see when the roller comes int play force will move the curved magnet in a certain direction. If the segment were there the magnet would not move. With this segment missing we can actually magnetize the arc and use it to create a TOMI track. When I first came across this idea I flipped out. I ran around dancing thinking I solved the riddle of the universe. Well not quite.

I still had to over come the magnetic lock. You see as you bring the runner(which we will now call the “Drive Magnet”) into play with this track, it still came to a halt when north met south.(magnetic lock). So what I came up with was a TOMI within a TOMI, as you can see in the diagram below left.

This is the heart of MAG-GEN. By placing a TOMI track within another TOMI track you create a partial loop in which by the slightest movement of the drive magnet you can be operating in one track then the other. I hope by the picture it is clear that these two tracks are not touching. They are on the same plane, and there is about a quarter inch gap in-between them. By not touching, their personal magnetic fields are kept strong and the magnetic loop is only partially created. What this does is create a magnetic path for the drive magnet (runner) to travel on.

The dark line here represents that path. Know that the magnetic tracks do not wobble. It is the lighter drive magnets that move on this path as the magnets spin Now by pancaking the drive magnet in between two of these double track TOMI setups you have MAG-GEN.In fact you can double the output of the device by using two or more drive magnets and having them move in time with each other. I have devised several ways of having the drive magnets travel their path. One of which would be a non-magnetic carriage connecting

In Stage 1 you see the drive arm with one drive magnet in the inner TOMI track, and the lower drive magnet in the outer TOMI track. This will cause a rotation of the entire disk that the TOMI tracks rest upon.

In Stage 2 you see the disk has rotated 90 degrees clockwise. The movement of the drive arm has been upwards. This movement is bringing the drive magnets into the in-between stage where they are now in both the outer TOMI tracks field and the field of the inner TOMI track. This is a transition stage for the MAG-GEN.

In Stage 3 You see another 90 degree clockwise rotation has occured. The drive magnets are in their full upright position. The upper drive magnet is now located completely in the outer TOMI tracks magnetic field and the lower drive magnet is completely in the inner TOMI tracks magnetic field.

In Stage 4 you see another 90 degrees has been turned in the clockwise direction. The drive arm is once again in the transition stage of movement. This is the stage where the drive arm is now crossing both of the TOMI tracks, and going down back to the original starting position that we found ourselves seeing in Stage 1.

There are many different ways in going about moving the drive magnets. Another that I have devised is to have a center gear built in to the disk then have two or more gears one to each side of the center gear each one containing a drive magnet that rotates back and fourth between the TOMI tracks.

One does not have to move the "drive magnet" in order to create motion in the rotor. In the previous paper the example description states that the rotor and the stator both move. Allow me to now show you how the stator can be stationary as it's name implies.

A cutaway from the original mag-gen rings shows the path a drive magnet travels when "jumping" tomi tracks. This is the point in mag-gen where the most amount of energy is created. However the original description is not the most efficient method to extract this energy. It is this "jumping of tracks that makes the mag-gen work.

1. By placing the TOMI tracks on the on the circumference of the rotor and not on the side one can still create energy.

2. By only using the sections of tomi tracks where there is a jump between the tracks you will be reducing the weight of the rotor.

3. And finally by leaning the tracks around 45 deg. you will have a directional flow of the magnetic fields to cause rotation.

Try this. On a flat plane, layout several TOMI tracks in a row side by side. All should be pointing north away from you. Now tilt the tops to your right about 40-45 deg. Tape these down so that they cannot escape each other. There should be a small gap between each track no more than an eighth of an inch.

Do not skew the tracks, keep them in their rectangular form.

Now bring in a large magnet and with its north pole held just above the center (from top to bottom) lower it to the tracks. Notice the hard pull/push to the left. Move it back and forth the length of your track and notice how even the pull is.

There are no gaps or weak points in the field. It is even. Even as I wrote the original mag-gen, I pointed out that this "jumping" of tracks is the heart of mag-gen.

I hope that this has been a proper enough explanation of my MAG-GEN concept for you to grasp the importance of what it implicates for the future.

There are many devices out there that have proven the existence of free energy and ways to create it. Search on your own and find these devices. All the major search engines will bring up many sites that describe different methods and devices that you can study to produce your own concepts. Draw your own conclusions about these machines.

Try not to be misled by shams and con artists. We can help the world, and it is me and you who has to do it. No one else is going to do that for us.

In the near future I hope to produce products that you can purchase using the concepts that I have described for you here.

In the mean time look up the information that is already available about free energy, hydrogen engines, water engines, pmm’s (perpetual motion machines), ram pumps, xogen, and motionless electromagnetic generators, and cold fusion.

Mag-Gen is needed in our society now!




Page 1 | 2 | 3 | 4